You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
69 lines
2.5 KiB
C
69 lines
2.5 KiB
C
/**
|
|
* \file
|
|
*
|
|
* \brief SAM D21 Xplained Pro board configuration.
|
|
*
|
|
* Copyright (c) 2013-2018 Microchip Technology Inc. and its subsidiaries.
|
|
*
|
|
* \asf_license_start
|
|
*
|
|
* \page License
|
|
*
|
|
* Subject to your compliance with these terms, you may use Microchip
|
|
* software and any derivatives exclusively with Microchip products.
|
|
* It is your responsibility to comply with third party license terms applicable
|
|
* to your use of third party software (including open source software) that
|
|
* may accompany Microchip software.
|
|
*
|
|
* THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES,
|
|
* WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE,
|
|
* INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY,
|
|
* AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE
|
|
* LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL
|
|
* LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE
|
|
* SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE
|
|
* POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT
|
|
* ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY
|
|
* RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY,
|
|
* THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE.
|
|
*
|
|
* \asf_license_stop
|
|
*
|
|
*/
|
|
/*
|
|
* Support and FAQ: visit <a href="https://www.microchip.com/support/">Microchip Support</a>
|
|
*/
|
|
|
|
#ifndef CONF_BOARD_H_INCLUDED
|
|
#define CONF_BOARD_H_INCLUDED
|
|
|
|
#include "conf_oracle.h"
|
|
|
|
// USART -- Debug HW Config
|
|
#define USART_DEBUG_MODULE SERCOM3
|
|
#define USART_DEBUG_PINMUX_PAD0 PINMUX_PA22C_SERCOM3_PAD0
|
|
#define USART_DEBUG_PINMUX_PAD1 PINMUX_PA23C_SERCOM3_PAD1
|
|
#define USART_DEBUG_PINMUX_PAD2 PINMUX_UNUSED
|
|
#define USART_DEBUG_PINMUX_PAD3 PINMUX_UNUSED
|
|
#define USART_DEBUG_BAUDRATE 115200
|
|
#define USART_DEBUG_MUX_SETTING USART_RX_1_TX_0_XCK_1
|
|
|
|
#define I2C_MASTER_MODULE SERCOM2
|
|
#define I2C_MASTER_PINMUX_PAD0 PINMUX_PA08D_SERCOM2_PAD0
|
|
#define I2C_MASTER_PINMUX_PAD1 PINMUX_PA09D_SERCOM2_PAD1
|
|
|
|
// GPIO -- SSD1963 Display Controller
|
|
#define SSD1963_TFT_DATA_MASK (0xFFFF)
|
|
#define SSD1963_TFT_DATA_PORT ((PortGroup*)&PORT->Group[1])
|
|
#define SSD1963_TFT_DATA_DIR PORT_PIN_DIR_OUTPUT
|
|
#define SSD1963_TFT_DATA_PULL PORT_PIN_PULL_NONE
|
|
|
|
#define SSD1963_TFT_nRST PIN_PA04
|
|
#define SSD1963_TFT_RSDC PIN_PA05
|
|
#define SSD1963_TFT_nCS PIN_PA06
|
|
#define SSD1963_TFT_WR PIN_PA07
|
|
#define SSD1963_TFT_RD PIN_PA10
|
|
|
|
|
|
#endif /* CONF_BOARD_H_INCLUDED */
|