You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

202 lines
6.3 KiB
C

3 years ago
/**
* \file
*
* \brief Port
*
* Copyright (c) 2014-2018 Microchip Technology Inc. and its subsidiaries.
*
* \asf_license_start
*
* \page License
*
* Subject to your compliance with these terms, you may use Microchip
* software and any derivatives exclusively with Microchip products.
* It is your responsibility to comply with third party license terms applicable
* to your use of third party software (including open source software) that
* may accompany Microchip software.
*
* THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES,
* WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE,
* INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY,
* AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE
* LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL
* LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE
* SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE
* POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT
* ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY
* RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY,
* THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE.
*
* \asf_license_stop
*/
#ifndef _HAL_GPIO_INCLUDED_
#define _HAL_GPIO_INCLUDED_
#include <hpl_gpio.h>
#include <utils_assert.h>
#ifdef __cplusplus
extern "C" {
#endif
/**
* \brief Set gpio pull mode
*
* Set pin pull mode, non existing pull modes throws an fatal assert
*
* \param[in] pin The pin number for device
* \param[in] pull_mode GPIO_PULL_DOWN = Pull pin low with internal resistor
* GPIO_PULL_UP = Pull pin high with internal resistor
* GPIO_PULL_OFF = Disable pin pull mode
*/
static inline void gpio_set_pin_pull_mode(const uint8_t pin, const enum gpio_pull_mode pull_mode)
{
_gpio_set_pin_pull_mode((enum gpio_port)GPIO_PORT(pin), pin & 0x1F, pull_mode);
}
/**
* \brief Set pin function
*
* Select which function a pin will be used for
*
* \param[in] pin The pin number for device
* \param[in] function The pin function is given by a 32-bit wide bitfield
* found in the header files for the device
*
*/
static inline void gpio_set_pin_function(const uint32_t pin, uint32_t function)
{
_gpio_set_pin_function(pin, function);
}
/**
* \brief Set port data direction
*
* Select if the pin data direction is input, output or disabled.
* If disabled state is not possible, this function throws an assert.
*
* \param[in] port Ports are grouped into groups of maximum 32 pins,
* GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc
* \param[in] mask Bit mask where 1 means apply direction setting to the
* corresponding pin
* \param[in] direction GPIO_DIRECTION_IN = Data direction in
* GPIO_DIRECTION_OUT = Data direction out
* GPIO_DIRECTION_OFF = Disables the pin
* (low power state)
*/
static inline void gpio_set_port_direction(const enum gpio_port port, const uint32_t mask,
const enum gpio_direction direction)
{
_gpio_set_direction(port, mask, direction);
}
/**
* \brief Set gpio data direction
*
* Select if the pin data direction is input, output or disabled.
* If disabled state is not possible, this function throws an assert.
*
* \param[in] pin The pin number for device
* \param[in] direction GPIO_DIRECTION_IN = Data direction in
* GPIO_DIRECTION_OUT = Data direction out
* GPIO_DIRECTION_OFF = Disables the pin
* (low power state)
*/
static inline void gpio_set_pin_direction(const uint8_t pin, const enum gpio_direction direction)
{
_gpio_set_direction((enum gpio_port)GPIO_PORT(pin), 1U << GPIO_PIN(pin), direction);
}
/**
* \brief Set port level
*
* Sets output level on the pins defined by the bit mask
*
* \param[in] port Ports are grouped into groups of maximum 32 pins,
* GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc
* \param[in] mask Bit mask where 1 means apply port level to the corresponding
* pin
* \param[in] level true = Pin levels set to "high" state
* false = Pin levels set to "low" state
*/
static inline void gpio_set_port_level(const enum gpio_port port, const uint32_t mask, const bool level)
{
_gpio_set_level(port, mask, level);
}
/**
* \brief Set gpio level
*
* Sets output level on a pin
*
* \param[in] pin The pin number for device
* \param[in] level true = Pin level set to "high" state
* false = Pin level set to "low" state
*/
static inline void gpio_set_pin_level(const uint8_t pin, const bool level)
{
_gpio_set_level((enum gpio_port)GPIO_PORT(pin), 1U << GPIO_PIN(pin), level);
}
/**
* \brief Toggle out level on pins
*
* Toggle the pin levels on pins defined by bit mask
*
* \param[in] port Ports are grouped into groups of maximum 32 pins,
* GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc
* \param[in] mask Bit mask where 1 means toggle pin level to the corresponding
* pin
*/
static inline void gpio_toggle_port_level(const enum gpio_port port, const uint32_t mask)
{
_gpio_toggle_level(port, mask);
}
/**
* \brief Toggle output level on pin
*
* Toggle the pin levels on pins defined by bit mask
*
* \param[in] pin The pin number for device
*/
static inline void gpio_toggle_pin_level(const uint8_t pin)
{
_gpio_toggle_level((enum gpio_port)GPIO_PORT(pin), 1U << GPIO_PIN(pin));
}
/**
* \brief Get input level on pins
*
* Read the input level on pins connected to a port
*
* \param[in] port Ports are grouped into groups of maximum 32 pins,
* GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc
*/
static inline uint32_t gpio_get_port_level(const enum gpio_port port)
{
return _gpio_get_level(port);
}
/**
* \brief Get level on pin
*
* Reads the level on pins connected to a port
*
* \param[in] pin The pin number for device
*/
static inline bool gpio_get_pin_level(const uint8_t pin)
{
return (bool)(_gpio_get_level((enum gpio_port)GPIO_PORT(pin)) & (0x01U << GPIO_PIN(pin)));
}
/**
* \brief Get current driver version
*/
uint32_t gpio_get_version(void);
#ifdef __cplusplus
}
#endif
#endif