You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
112 lines
4.1 KiB
C
112 lines
4.1 KiB
C
/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
|
|
/*
|
|
* usr/include/linux/lp.h c.1991-1992 James Wiegand
|
|
* many modifications copyright (C) 1992 Michael K. Johnson
|
|
* Interrupt support added 1993 Nigel Gamble
|
|
* Removed 8255 status defines from inside __KERNEL__ Marcelo Tosatti
|
|
*/
|
|
#ifndef _LINUX_LP_H
|
|
#define _LINUX_LP_H
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/ioctl.h>
|
|
|
|
/*
|
|
* Per POSIX guidelines, this module reserves the LP and lp prefixes
|
|
* These are the lp_table[minor].flags flags...
|
|
*/
|
|
#define LP_EXIST 0x0001
|
|
#define LP_SELEC 0x0002
|
|
#define LP_BUSY 0x0004
|
|
#define LP_BUSY_BIT_POS 2
|
|
#define LP_OFFL 0x0008
|
|
#define LP_NOPA 0x0010
|
|
#define LP_ERR 0x0020
|
|
#define LP_ABORT 0x0040
|
|
#define LP_CAREFUL 0x0080 /* obsoleted -arca */
|
|
#define LP_ABORTOPEN 0x0100
|
|
|
|
#define LP_TRUST_IRQ_ 0x0200 /* obsolete */
|
|
#define LP_NO_REVERSE 0x0400 /* No reverse mode available. */
|
|
#define LP_DATA_AVAIL 0x0800 /* Data is available. */
|
|
|
|
/*
|
|
* bit defines for 8255 status port
|
|
* base + 1
|
|
* accessed with LP_S(minor), which gets the byte...
|
|
*/
|
|
#define LP_PBUSY 0x80 /* inverted input, active high */
|
|
#define LP_PACK 0x40 /* unchanged input, active low */
|
|
#define LP_POUTPA 0x20 /* unchanged input, active high */
|
|
#define LP_PSELECD 0x10 /* unchanged input, active high */
|
|
#define LP_PERRORP 0x08 /* unchanged input, active low */
|
|
|
|
/* timeout for each character. This is relative to bus cycles -- it
|
|
* is the count in a busy loop. THIS IS THE VALUE TO CHANGE if you
|
|
* have extremely slow printing, or if the machine seems to slow down
|
|
* a lot when you print. If you have slow printing, increase this
|
|
* number and recompile, and if your system gets bogged down, decrease
|
|
* this number. This can be changed with the tunelp(8) command as well.
|
|
*/
|
|
|
|
#define LP_INIT_CHAR 1000
|
|
|
|
/* The parallel port specs apparently say that there needs to be
|
|
* a .5usec wait before and after the strobe.
|
|
*/
|
|
|
|
#define LP_INIT_WAIT 1
|
|
|
|
/* This is the amount of time that the driver waits for the printer to
|
|
* catch up when the printer's buffer appears to be filled. If you
|
|
* want to tune this and have a fast printer (i.e. HPIIIP), decrease
|
|
* this number, and if you have a slow printer, increase this number.
|
|
* This is in hundredths of a second, the default 2 being .05 second.
|
|
* Or use the tunelp(8) command, which is especially nice if you want
|
|
* change back and forth between character and graphics printing, which
|
|
* are wildly different...
|
|
*/
|
|
|
|
#define LP_INIT_TIME 2
|
|
|
|
/* IOCTL numbers */
|
|
#define LPCHAR 0x0601 /* corresponds to LP_INIT_CHAR */
|
|
#define LPTIME 0x0602 /* corresponds to LP_INIT_TIME */
|
|
#define LPABORT 0x0604 /* call with TRUE arg to abort on error,
|
|
FALSE to retry. Default is retry. */
|
|
#define LPSETIRQ 0x0605 /* call with new IRQ number,
|
|
or 0 for polling (no IRQ) */
|
|
#define LPGETIRQ 0x0606 /* get the current IRQ number */
|
|
#define LPWAIT 0x0608 /* corresponds to LP_INIT_WAIT */
|
|
/* NOTE: LPCAREFUL is obsoleted and it' s always the default right now -arca */
|
|
#define LPCAREFUL 0x0609 /* call with TRUE arg to require out-of-paper, off-
|
|
line, and error indicators good on all writes,
|
|
FALSE to ignore them. Default is ignore. */
|
|
#define LPABORTOPEN 0x060a /* call with TRUE arg to abort open() on error,
|
|
FALSE to ignore error. Default is ignore. */
|
|
#define LPGETSTATUS 0x060b /* return LP_S(minor) */
|
|
#define LPRESET 0x060c /* reset printer */
|
|
#ifdef LP_STATS
|
|
#define LPGETSTATS 0x060d /* get statistics (struct lp_stats) */
|
|
#endif
|
|
#define LPGETFLAGS 0x060e /* get status flags */
|
|
#define LPSETTIMEOUT_OLD 0x060f /* set parport timeout */
|
|
#define LPSETTIMEOUT_NEW \
|
|
_IOW(0x6, 0xf, __s64[2]) /* set parport timeout */
|
|
#if __BITS_PER_LONG == 64
|
|
#define LPSETTIMEOUT LPSETTIMEOUT_OLD
|
|
#else
|
|
#define LPSETTIMEOUT (sizeof(time_t) > sizeof(__kernel_long_t) ? \
|
|
LPSETTIMEOUT_NEW : LPSETTIMEOUT_OLD)
|
|
#endif
|
|
|
|
/* timeout for printk'ing a timeout, in jiffies (100ths of a second).
|
|
This is also used for re-checking error conditions if LP_ABORT is
|
|
not set. This is the default behavior. */
|
|
|
|
#define LP_TIMEOUT_INTERRUPT (60 * HZ)
|
|
#define LP_TIMEOUT_POLLED (10 * HZ)
|
|
|
|
|
|
#endif /* _LINUX_LP_H */
|